Obtaining Service During. Warranty Period New editions are complete revisions of the manual. Change sheets, which may be The HP DesignJet CM printer is an E/A0 size large-format inkjet printer which can print in. Download HP DESIGNJET , C, CT, CM SERVICE MANUAL service manual & repair info for electronics experts. Download DesignJet , C, Cplus, CM Service from folder Printers DesignJet. Service Manual pdf. From folder: Printers HP DesignJet.
| Author: | Mezihn Akitaur |
| Country: | Tajikistan |
| Language: | English (Spanish) |
| Genre: | Science |
| Published (Last): | 2 July 2011 |
| Pages: | 172 |
| PDF File Size: | 17.84 Mb |
| ePub File Size: | 13.81 Mb |
| ISBN: | 808-2-47711-514-8 |
| Downloads: | 9552 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Doujora |
HP DesignJet cm Printer User Guides | HP® Customer Support
If this does not fix the problem, troubleshoot the X-axis system mark position test page Carriage sensor does not correctly find media edge. Primer stepper motor Bail stepper motor Wiper stepper motor Primer 6 Disconnect the short motor cable from the cable assembly to the main PCA. Primer Stepper Motor The primer stepper motor 75cm mounted on the plotter’s left side-plate and connects to the main PCA through the service-station cable.
Maintenance Kit – Maintenance kit – Includes service station spittoon assembly, carriage Y-Axis motor, encoder strip, and lubricating oil.
When rotated in the opposite direction, a clutch engages a diaphragm to provide the vacuum for priming. Do not use abrasive cleaners.
Extended warranty option is available. The first column depicts the block of text shown on the plot but the remaining blocks show the memory location number instead of the contents at each position on the text block. Remove drsignjet the cartridges to start the test. Once the plotter is reset, it uses the default values until another user calibration is done.
RSC communications are handled by a universal asynchronous receiver-transmitter UART and baud rate generator built into the processor-support application-specific integrated circuit ASIC. The problem affects only E-size plotters.
Set to “Best” – Paper Type Media setting: Paper – Heavyweight coated paper – 61cm 24in x Some third party media types have unacceptable results. Remove any media already loaded into the plotter before performing the servicr. With HP Kanual, you can protect your investment and ensure its maximum availability.
HP Troubleshooting page for CB DesignJet CM Printer
Perform the drop detect calibration whenever the: Level of Plotter Usage These are the usage limits of the plotter: If printing in color, the problem never appears if the line width is 5. Paper – Translucent bond 755ccm – E size 34 x inches – sheets.
Paper – Opaque bond paper – Architectural E size 36 x inches – sheets. Graphics Languages The plotters accept drawing data in the following graphics languages: See the table on page for a numerical listing of possible error codes. If any of the above problems are visible on the nozzle print, try one of the following: Rerun pen alignment page When media is loaded, both levers are rotated, thus clearing the optical path and changing the sensor state from open to closed.
Align the holes on the gear with the holes on the shaft. If the plotter hangs up during a test, switch the plotter OFF and restart at step 1 again.
Ensure that the two flags on the media sensor are correctly positioned. By default, the problems solved are ajfecting all the previous releases. Procedures reserved for service use are available through the ”Service Tests” menu, which is a subset of the “Utilities” menu.
Europe, Middle East, Africa. Warm-up pulses are generated when in the “Warm-up When Idle” mode. Low-noise or noiseless, clean ground earth terminal.
HP DesignJet 755cm Printer User Guides
Follow these warnings and cautions for your protection and to avoid damaging the plotter. Paper – Translucent bond paper – 61cm 24in x Wrong Cartridge Type Swrvice have loaded one or more incompatible cartridges. Causes The following are the main causes of this problem: Perform the area fill PQ plot test as follows: The material on which the graphics are plotted: