LMH/ Texas Instruments Linear Voltage Regulators LMH/ Voltage Regulator datasheet, inventory, & pricing. The LM/LMC is a voltage regulator designed prima- rily for series regulator applications. By itself, it will supply output currents up to mA; but external. The LM is a monolithic integrated programmable voltage regulator, assembled in. lead dual in-line plastic package. The circuit provides internal current.

Author: Goshura Totilar
Country: France
Language: English (Spanish)
Genre: Travel
Published (Last): 13 October 2015
Pages: 419
PDF File Size: 13.38 Mb
ePub File Size: 7.98 Mb
ISBN: 548-9-73408-934-1
Downloads: 44012
Price: Free* [*Free Regsitration Required]
Uploader: Arashigore

For getting an output voltage range from 2v to 7v you can use the circuit below, which is a Basic Voltage Regulator circuit using LM voltage regulator IC. I have a basic grasp on their operation, getting more familiar with small signal characteristics, etc, but besides knowing the is the pass transistor and power transistor, that’s about it.

This terminal is directly supplied from the supply when not connected to series pass transistor. As for the zener diode question I’m sorry that wasn’t very clear. The error amplifier 4 5 inputs is used to compare a reference voltage with the voltage to be controlled. It is a pin IC that needs some outboard components to tell it what to do. Agreed – the inverting pin is fed by a very “interesting” arrangement – in fact that’s the exact part that confuses me besides the Vz being pulled to ground.


I think the is okay because I did swap it with another with no difference.

Also able to use as either linear or switching type regulator. I’ll run a test on these today when I get out of lm723hh lab.

National Semiconductor

I tested it with a 5-ohm power resistor. Oh man, can’t wait to read this.

If you are only trying to build a volt 2 amp power supply, there are better ways to do it in Pin configuration Pin No.

The datasueet was published in the August edition of 73 Magazine, and may be viewed at archive. I am familiar with the but don’t think I’ve ever actually used one datsheet now I’m going to look into them as well as an interim PS would be nice The design followed relatiovely logically from what was available at that time.

A was used to regulate the HV output 15KV. In a metal can: Q2 is a current limiter. Then study the example application circuits given in it.

Voltage Regulator

First, the LM has a maximum allowable input voltage of 40 volts. Post as a guest Name. Pin 6 provides a buffered reference voltage – the forerunner of a modern bandgap reference.

Home Questions Tags Users Unanswered.

Sign datashest using Facebook. As Q1 is a TO92 package with dissipation well under 1 Watt this is probably why it exploded – summat went aglae, the tried to turn on to cause Vout to rise by turning on Q1 to turn on Q3, the cct did not comply so it kept turning Q1 on and it gave up dur to the ‘s base current.


None the less, I’m going to look up the datasheet and give her a test. Q2 is for short-circuit protection- it detects the voltage across R However, I don’t understand: If it is a 1 Watt it might last a long time.

LM was the bees knees voltage regulator controller and maybe also the only one readily available ‘way back when’. LM data sheet here.

LMH Datasheet(PDF) – National Semiconductor (TI)

Closing lm723g be very sad. The negative Vout will dwtasheet course not happen with a ground referenced positive input supply, but would be possible if Vin was referenced against some negative value. Go above this and kaput! Put the sense resistor divider on the Vout side of the resistors. If you use a resistor to turn the on and the to turn it off, the will need to be sinkig most of the current when idle and so must be used near its current rating often.